Thrusters

OYS Vertical Retracting Rotating Thrusters Electric


oys-vertical-retracting-rotating-thrusterVR Series vertical retracting thrusters benefit from the same in-hub technology as our T Series thrusters, whilst allowing the thruster to fully retract leaving a fair hull with minimal drag. This compact design uses a lead screw lift assembly with a reduction gearbox to ensure that the thruster hub when retracted is held firmly in place. The VR Series thruster deploys vertically and can rotate 360 degrees whilst thrusting. Having steerable thrust provides ultimate manoeuvrability for berthing or in conjunction with any dynamic positioning system.

Part Number Max Power (kW) Max Power (Hp) Thrust (Kgf) Thrust (Lbs) Prop Diameter (mm) Prop Diameter (in)
E-0250-VR 25 33 300 661 255 10
E-0300-VR 36 48 432 952 305 12
E-0400-VR 63 85 756 1667 406 16
E-0500-VR 99 133 1188 2619 508 20
E-0600-VR 142 191 1704 3757 610 24
E-0700-VR 194 260 2328 5132 711 28
E-0800-VR 252 338 2772 6111 813 32
E-1000-VR 393 527 4323 9506 1016 40
E-1200-VR 565 758 6215 13702 1219 48
E-1400-VR 768 1030 8448 18624 1422 56

Permanent Magnet Motor on Request

DFA-0500-E

OYS Fixed Drive Leg
Electric


Specifications
Max Power 30 kW (40 Hp)
Prop Diameter 500 mm (20 in)

DFA-0575-E

OYS Fixed Drive Leg
Electric


Specifications
Max Power 75 kW (101 Hp)
Prop Diameter 500 mm (20 in)

DFA-0650-E

OYS Fixed Drive Leg
Electric


Specifications
Max Power 150 kW (201 Hp)
Prop Diameter 650 mm (26 in)

DFA-0750-E

OYS Fixed Drive Leg
Electric


Specifications
Max Power 250 kW (335 Hp)
Prop Diameter 750 mm (30 in)

E-0250-S

OYS Swing Thruster
Electric


Specifications
Max Power 25 kW (33 Hp)
Thrust 300 Kgf (661 Lbf)
Prop Diameter 255 mm (10 in)

E-0250-T

Tunnel Thruster
Electric


Specifications
Max Power 25 kW (33 Hp)
Thrust 300 Kgf (661 Lbf)
Prop Diameter 255 mm (10 in)

E-0250-V

OYS Vertical Retracting Thruster
Electric


Specifications
Max Power 25 kW (33 Hp)
Thrust 300 Kgf (661 Lbf)
Prop Diameter 255 mm (10 in)

E-0256-VR

OYS Vertical Retracting Rotating Thruster
Electric


Specifications
Max Power 25 kW (33 Hp)
Thrust 300 Kgf (661 Lbf)
Prop Diameter 255 mm (10 in)

E-0300-S

OYS Swing Thruster
Electric

The OYS swing thruster benefits from the same in-hub technology as the fixed tunnel thruster, whilst allowing the thruster to fully retract leaving a fair hull with minimal drag. These types of thrusters are usually used in applications where they are positioned within the accommodation area of a vessel. The low profile and compact design allows them to be easily fitted below floor bearers or in low level lockers, under beds or among other locations.

This compact design uses a lead screw lift assembly with a reduction gear box to ensure that the thruster hub, when retracted is held firmly in place and cannot move. In addition, OYS swing thrusters feature a locking pin which adds additional security when locking the leg in the raised position. The main drive motor and hydraulic hoses or cables are fully enclosed within the upper leg assembly so are not open to sea water. OYS has worked with a number of boat builders to optimise the range offered.

E-0300-S
OYS E-0300-S Thruster
Specifications
Max Power 36 kW (48 Hp)
Thrust 432 Kgf (952 Lbf)
Prop Diameter 305 mm (12 in)
Downloads
Swing Thruster E-0300-S
PDF Download   DWG Download   STP Download  

E-0300-T

OYS Tunnel Thruster
Electric


Specifications
Max Power 36 kW (48 Hp)
Thrust 432 Kgf (952 Lbf)
Prop Diameter 305 mm (12 in)

E-0300-V

OYS Vertical Retracting Thruster
Electric


Specifications
Max Power 36 kW (48 Hp)
Thrust 432 Kgf (952 Lbf)
Prop Diameter 305 mm (12 in)

E-0300-VR

OYS Vertical Retracting Rotating Thruster
Electric


Specifications
Max Power 36 kW (48 Hp)
Thrust 432 Kgf (952 Lbf)
Prop Diameter 305 mm (12 in)

E-0400-S

OYS Swing Thruster
Electric

The OYS swing thruster benefits from the same in-hub technology as the fixed tunnel thruster, whilst allowing the thruster to fully retract leaving a fair hull with minimal drag. These types of thrusters are usually used in applications where they are positioned within the accommodation area of a vessel. The low profile and compact design allows them to be easily fitted below floor bearers or in low level lockers, under beds or among other locations.

This compact design uses a lead screw lift assembly with a reduction gear box to ensure that the thruster hub, when retracted is held firmly in place and cannot move. In addition, OYS swing thrusters feature a locking pin which adds additional security when locking the leg in the raised position. The main drive motor and hydraulic hoses or cables are fully enclosed within the upper leg assembly so are not open to sea water. OYS has worked with a number of boat builders to optimise the range offered.

E-0400-S

Specifications
Max Power 63 kW (85 Hp)
Thrust 756 Kgf (1667 Lbf)
Prop Diameter 406 mm (16 in)
Downloads
Swin Thruster E-0400-S
PDF Download   DWG Download   STP Download  

E-0400-T

OYS Tunnel Thruster
Electric


Specifications
Max Power 63 kW (85 Hp)
Thrust 756 Kgf (1667 Lbf)
Prop Diameter 406 mm (16 in)

E-0400-V

OYS Vertical Retracting Thruster
Electric


Specifications
Max Power 63 kW (85 Hp)
Thrust 756 Kgf (1667 Lbf)
Prop Diameter 406 mm (16 in)

E-0400-VR

OYS Vertical Retracting Rotating Thruster
Electric


Specifications
Max Power 63 kW (85 Hp)
Thrust 756 Kgf (1667 Lbf)
Prop Diameter 406 mm (16 in)

E-0500-S

OYS Swing Thruster
Electric


Specifications
Max Power 99 kW (133 Hp)
Thrust 1188 Kgf (2619 Lbf)
Prop Diameter 508 mm (20 in)

E-0500-T

OYS Tunnel Thruster
Electric


Specifications
Max Power 99 kW (133 Hp)
Thrust 1188 Kgf (2619 Lbf)
Prop Diameter 508 mm (20 in)

E-0500-V

OYS Vertical Retracting Thruster
Electric


Specifications
Max Power 99 kW (133 Hp)
Thrust 1188 Kgf (2619 Lbf)
Prop Diameter 508 mm (20 in)

E-0500-VR

OYS Vertical Retracting Rotating Thruster
Electric


Specifications
Max Power 99 kW (133 Hp)
Thrust 1188 Kgf (2619 Lbf)
Prop Diameter 508 mm (20 in)

E-0600-S

OYS Swing Thruster
Electric


Specifications
Max Power 142 kW (191 Hp)
Thrust 1704 Kgf (3757 Lbf)
Prop Diameter 610 mm (24 in)

E-0600-T

OYS Tunnel Thruster
Electric


Specifications
Max Power 142 kW (191 Hp)
Thrust 1704 Kgf (3757 Lbf)
Prop Diameter 610 mm (24 in)

E-0600-V

OYS Vertical Retracting Thruster
Electric


Specifications
Max Power 142 kW (191 Hp)
Thrust 1704 Kgf (3757 Lbf)
Prop Diameter 610 mm (24 in)

E-0600-VR

OYS Vertical Retracting Rotating Thruster
Electric


Specifications
Max Power 142 kW (191 Hp)
Thrust 1704 Kgf (3757 Lbf)
Prop Diameter 610 mm (24 in)

E-0700-S

OYS Swing Thruster
Electric


Specifications
Max Power 194 kW (260 Hp)
Thrust 2328 Kgf (5132 Lbf)
Prop Diameter 711 mm (28 in)

E-0700-T

OYS Tunnel Thruster
Electric


Specifications
Max Power 194 kW (260 Hp)
Thrust 2328 Kgf (5132 Lbf)
Prop Diameter 711 mm (28 in)

E-0700-V

OYS Vertical Retracting Thruster
Electric


Specifications
Max Power 194 kW (260 Hp)
Thrust 2328 Kgf (5132 Lbf)
Prop Diameter 711 mm (28 in)

E-0700-VR

OYS Vertical Retracting Rotating Thruster
Electric


Specifications
Max Power 194 kW (260 Hp)
Thrust 2328 Kgf (5132 Lbf)
Prop Diameter 711 mm (28 in)

E-0800-S

OYS Swing Thruster
Electric


Specifications
Max Power 252 kW (338 Hp)
Thrust 2772 Kgf (6111 Lbf)
Prop Diameter 813 mm (32 in)

E-0800-T

OYS Tunnel Thruster
Electric


Specifications
Max Power 252 kW (338 Hp)
Thrust 2772 Kgf (6111 Lbf)
Prop Diameter 813 mm (32 in)

E-0800-V

OYS Vertical Retracting Thruster
Electric


Specifications
Max Power 252 kW (338 Hp)
Thrust 2772 Kgf (6111 Lbf)
Prop Diameter 813 mm (32 in)

E-0800-VR

OYS Vertical Retracting Rotating Thruster
Electric


Specifications
Max Power 252 kW (338 Hp)
Thrust 2772 Kgf (6111 Lbf)
Prop Diameter 813 mm (32 in)

E-0900-S

OYS Swing Thruster
Electric


Specifications
Max Power 319 kW (428 Hp)
Thrust 3509 Kgf (7736 Lbf)
Prop Diameter 914 mm (36 in)

E-0900-T

OYS Tunnel Thruster
Electric


Specifications
Max Power 319 kW (428 Hp)
Thrust 3509 Kgf (7739 Lbf)
Prop Diameter 914 mm (36 in)

E-0900-V

OYS Vertical Retracting Thruster
Electric


Specifications
Max Power 319 kW (428 Hp)
Thrust 3509 Kgf (7736 Lbf)
Prop Diameter 914 mm (36 in)

E-0900-VR

OYS Vertical Retracting Rotating Thruster
Electric


Specifications
Max Power 319 kW (428 Hp)
Thrust 3509 Kgf (7736 Lbf)
Prop Diameter 914 mm (36 in)

E-1000-S

OYS Swing Thruster
Electric


Specifications
Max Power 393 kW (527 Hp)
Thrust 4323 Kgf (9506 Lbf)
Prop Diameter 1016 mm (40 in)

E-1000-T

OYS Tunnel Thruster
Electric


Specifications
Max Power 393 kW (527 Hp)
Thrust 4323 Kgf (9506 Lbf)
Prop Diameter 1016 mm (40 in)

E-1000-V

OYS Vertical Retracting Thruster
Electric


Specifications
Max Power 393 kW (527 Hp)
Thrust 4323 Kgf (9506 Lbf)
Prop Diameter 1016 mm (40 in)

E-1000-VR

OYS Vertical Retracting Rotating Thruster
Electric


Specifications
Max Power 393 kW (527 Hp)
Thrust 4323 Kgf (9506 Lbf)
Prop Diameter 1016 mm (40 in)

E-1100-S

OYS Swing Thruster
Electric


Specifications
Max Power 476 kW (638 Hp)
Thrust 5236 Kgf (11543 Lbf)
Prop Diameter 1118 mm (44 in)

E-1100-T

OYS Tunnel Thruster
Electric


Specifications
Max Power 476 kW (638 Hp)
Thrust 5236 Kgf (11543 Lbf)
Prop Diameter 1118 mm (44 in)

E-1100-V

OYS Vertical Retracting Thruster
Electric


Specifications
Max Power 476 kW (638 Hp)
Thrust 5236 Kgf (11543 Lbf)
Prop Diameter 1118 mm (44 in)

E-1100-VR

OYS Vertical Retracting Rotating Thruster
Electric


Specifications
Max Power 476 kW (638 Hp)
Thrust 5236 Kgf (11543 Lbf)
Prop Diameter 1118 mm (44 in)

E-1200-E

OYS Swing Thruster
Electric


Specifications
Max Power 565 kW (758 Hp)
Thrust 6215 Kgf (13702 Lbf)
Prop Diameter 1219 mm (48 in)

E-1200-T

OYS Tunnel Thruster
Electric


Specifications
Max Power 565 kW (758 Hp)
Thrust 6215 Kgf (13702 Lbf)
Prop Diameter 1219 mm (48 in)

E-1200-V

OYS Vertical Retracting Thruster
Electric


Specifications
Max Power 565 kW (758 Hp)
Thrust 6215 Kgf (13702 Lbf)
Prop Diameter 1219 mm (48 in)

E-1200-VR

OYS Vertical Retracting Rotating Thruster
Electric


Specifications
Max Power 565 kW (758 Hp)
Thrust 6215 Kgf (13702 Lbf)
Prop Diameter 1219 mm (48 in)

E-1300-S

OYS Swing Thruster
Electric


Specifications
Max Power 663 kW (889 Hp)
Thrust 7293 Kgf (16078 Lbf)
Prop Diameter 1321 mm (52 in)

E-1300-T

OYS Tunnel Thruster
Electric


Specifications
Max Power 663 kW (889 Hp)
Thrust 7293 Kgf (16078 Lbf)
Prop Diameter 1321 mm (52 in)

E-1300-V

OYS Vertical Retracting Thruster
Electric


Specifications
Max Power 663 kW (889 Hp)
Thrust 7293 Kgf (16078 Lbf)
Prop Diameter 1321 mm (52 in)

E-1300-VR

OYS Vertical Retracting Rotating Thruster
Electric


Specifications
Max Power 663 kW (889 Hp)
Thrust 7293 Kgf (16078 Lbf)
Prop Diameter 1321 mm (52 in)

E-1400-S

OYS Swing Thruster
Electric


Specifications
Max Power 768 kW (1030 Hp)
Thrust 8448 Kgf (18624 Lbf)
Prop Diameter 1422 mm (56 in)

E-1400-T

OYS Tunnel Thruster
Electric


Specifications
Max Power 768 kW (1030 Hp)
Thrust 8448 Kgf (18624 Lbf)
Prop Diameter 1422 mm (56 in)

E-1400-V

OYS Vertical Retracting Thruster
Electric


Specifications
Max Power 768 kW (1030 Hp)
Thrust 8448 Kgf (18624 Lbf)
Prop Diameter 1422 mm (56 in)

E-1400-VR

OYS Vertical Retracting Rotating Thruster
Electric


Specifications
Max Power 768 kW (1030 Hp)
Thrust 8448 Kgf (18624 Lbf)
Prop Diameter 1422 mm (56 in)

H-0250-S

OYS Swing Thruster
Hydraulic

The OYS Swing Thruster benefits from the same in-hub technology as our fixed tunnel thruster, whilst allowing the thruster to fully retract leaving a fair hull with minimal drag. These types of thrusters are usually used in applications where they are positioned within the accommodation area of a vessel. The low profile and compact design allows them to be easily fitted below floor bearers or in low-level lockers / under beds etc.

This compact design uses a lead screw lift assembly with a reduction gear box to ensure that the thruster hub when retracted is held firmly in place and cannot move. In addition, OYS swing thrusters feature a locking pin which adds additional security when locking the leg in the raised position. The main drive motor and hydraulic hoses or cables are fully enclosed within the upper leg assembly so are not open to sea water. OYS has worked with a number of boat builders to optimise the range offered.

H-0250-S
H-0250-S
Specifications
Max Power 25 kW (33 Hp)
Thrust 300 Kgf (661 Lbf)
Prop Diameter 255 mm (10 in)
Downloads
Swing Thrusters H-0250-S
PDF Download   DWG Download   STP Download  

H-0250-T

OYS Tunnel Thruster
Hydraulic

T Series tunnel thrusters are compact and easy to fit units that can be supplied complete with steel, aluminium or composite tunnels, pre-drilled ready for installation.

The thruster hub units are protected by twin shaft seals on each propeller shaft and a single shaft seal on the vertical input shaft. The tunnel thruster uses high torque spiral bevel gears and twin contra-rotating propellers to develop a high thrust to tunnel diameter ratio.

T Series thrusters are supplied complete with a mounting saddle, all gaskets/fasteners and a suitable interface for any hydraulic or electric motor. The motor is driven via a flexible coupling to reduce noise and vibration

H-0250-T
H-0250-T
Specifications
Max Power 25 kW (33 Hp)
Thrust 300 Kgf (661 Lbf)
Prop Diameter 255 mm (10 in)
Downloads
Tunnel Thrusters H-0250-T
PDF Download   DWG Download   STP Download  

H-0250-V

OYS Vertical Retracting Thruster
Hydraulic

V Series vertical retracting thrusters benefit from the same in-hub technology as our T Series thrusters, whilst allowing the thruster to fully retract leaving a fair hull with minimal drag. This compact design uses a lead screw lift assembly with a reduction gearbox to ensure that the thruster hub when retracted is held firmly in place.

The Vertical Thruster is also very useful where vessels have a deep V profile so the thruster is fitted higher providing a longer deployment stroke to clear the hull. They can also be fitted further forward or aft than a conventional Tunnel Thrusters increasing the turning moment of the hull and therefore requiring less power input.

For added security, all V Series thrusters can be manually lifted in case of power failure. To ensure there is no environmental risk, the main drive motor, hydraulic hoses and electric cables are inside the vessel so are not open to seawater.

H-0250-V
H-0250-V
Specifications
Max Power 25 kW (33 Hp)
Thrust 300 Kgf (661 Lbf)
Prop Diameter 255 mm (10 in)
Downloads
Vertical Thrusters H-0250-V
PDF Download   DWG Download   STP Download  

H-0250-VR

OYS Vertical Retracting Rotating Thruster
Hydraulic


Specifications
Max Power 25 kW (33 Hp)
Thrust 300 Kgf (661 Lbf)
Prop Diameter 255 mm (10 in)

H-0300-S

OYS Swing Thrusters
Hydraulic

The OYS Swing Thruster benefits from the same in-hub technology as our fixed tunnel thruster, whilst allowing the thruster to fully retract leaving a fair hull with minimal drag. These types of thrusters are usually used in applications where they are positioned within the accommodation area of a vessel. The low profile and compact design allows them to be easily fitted below floor bearers or in low-level lockers / under beds etc.

This compact design uses a lead screw lift assembly with a reduction gear box to ensure that the thruster hub when retracted is held firmly in place and cannot move. In addition, OYS swing thrusters feature a locking pin which adds additional security when locking the leg in the raised position. The main drive motor and hydraulic hoses or cables are fully enclosed within the upper leg assembly so are not open to sea water. OYS has worked with a number of boat builders to optimise the range offered.

H-0300-S
H-0300-S
Specifications
Max Power 36 kW (48 Hp)
Thrust 432 Kgf (952 Lbf)
Prop Diameter 305 mm (12 in)
Downloads
Swing Thrusters H-0300-S
PDF Download   DWG Download   STP Download  

H-0300-T

OYS Tunnel Thruster
Hydraulic

T Series tunnel thrusters are compact and easy to fit units that can be supplied complete with steel, aluminium or composite tunnels, pre-drilled ready for installation.

The thruster hub units are protected by twin shaft seals on each propeller shaft and a single shaft seal on the vertical input shaft. The tunnel thruster uses high torque spiral bevel gears and twin contra-rotating propellers to develop a high thrust to tunnel diameter ratio.

T Series thrusters are supplied complete with a mounting saddle, all gaskets/fasteners and a suitable interface for any hydraulic or electric motor. The motor is driven via a flexible coupling to reduce noise and vibration.

H-0300-T
H-0300-T
Specifications
Max Power 36 kW (48 Hp)
Thrust 432 Kgf (952 Lbf)
Prop Diameter 305 mm (12 in)
Downloads
Tunnel Thrusters H-0300-T
PDF Download   DWG Download   STP Download  

H-0300-V

OYS Vertical Retracting Thruster
Hydraulic

V Series vertical retracting thrusters benefit from the same in-hub technology as our T Series thrusters, whilst allowing the thruster to fully retract leaving a fair hull with minimal drag. This compact design uses a lead screw lift assembly with a reduction gearbox to ensure that the thruster hub when retracted is held firmly in place.

The Vertical Thruster is also very useful where vessels have a deep V profile so the thruster is fitted higher providing a longer deployment stroke to clear the hull. They can also be fitted further forward or aft than a conventional Tunnel Thrusters increasing the turning moment of the hull and therefore requiring less power input.

For added security, all V Series thrusters can be manually lifted in case of power failure. To ensure there is no environmental risk, the main drive motor, hydraulic hoses and electric cables are inside the vessel so are not open to seawater.

H-0300-V
H-0300-V
Specifications
Max Power 36 kW (48 Hp)
Thrust 432 Kgf (952 Lbf)
Prop Diameter 305 mm (12 in)
Downloads
Vertical Thrusters H-0300-V
PDF Download   DWG Download   STP Download  

H-0300-VR

OYS Vertical Retracting Rotating Thruster
Hydraulic


Specifications
Max Power 36 kW (48 Hp)
Thrust 432 Kgf (952 Lbf)
Prop Diameter 305 mm (12 in)

H-0400-S

OYS Swing Thruster
Hydraulic

The OYS Swing Thruster benefits from the same in-hub technology as our fixed tunnel thruster, whilst allowing the thruster to fully retract leaving a fair hull with minimal drag. These types of thrusters are usually used in applications where they are positioned within the accommodation area of a vessel. The low profile and compact design allows them to be easily fitted below floor bearers or in low-level lockers / under beds etc.

This compact design uses a lead screw lift assembly with a reduction gear box to ensure that the thruster hub when retracted is held firmly in place and cannot move. In addition, OYS swing thrusters feature a locking pin which adds additional security when locking the leg in the raised position. The main drive motor and hydraulic hoses or cables are fully enclosed within the upper leg assembly so are not open to sea water. OYS has worked with a number of boat builders to optimise the range offered.

H-0400-S
H-0400-S
Specifications
Max Power 63 kW (85 Hp)
Thrust 756 Kgf (1667 Lbf)
Prop Diameter 406 mm (16 in)
Downloads
Swing Thrusters H-0400-S
PDF Download   DWG Download   STP Download  

H-0400-T

OYS Tunnel Thruster
Hydraulic

T Series tunnel thrusters are compact and easy to fit units that can be supplied complete with steel, aluminium or composite tunnels, pre-drilled ready for installation.

The thruster hub units are protected by twin shaft seals on each propeller shaft and a single shaft seal on the vertical input shaft. The tunnel thruster uses high torque spiral bevel gears and twin contra-rotating propellers to develop a high thrust to tunnel diameter ratio.

T Series thrusters are supplied complete with a mounting saddle, all gaskets/fasteners and a suitable interface for any hydraulic or electric motor. The motor is driven via a flexible coupling to reduce noise and vibration.

H-0400-T
H-0400-T
Specifications
Max Power 63 kW (85 Hp)
Thrust 756 Kgf (1667 Lbf)
Prop Diameter 406 mm (16 in)
Downloads
Tunnel Thrusters H-0400-T
PDF Download   DWG Download   STP Download  

H-0400-V

OYS Vertical Retracting Thruster
Hydraulic

V Series vertical retracting thrusters benefit from the same in-hub technology as our T Series thrusters, whilst allowing the thruster to fully retract leaving a fair hull with minimal drag. This compact design uses a lead screw lift assembly with a reduction gearbox to ensure that the thruster hub when retracted is held firmly in place.

The Vertical Thruster is also very useful where vessels have a deep V profile so the thruster is fitted higher providing a longer deployment stroke to clear the hull. They can also be fitted further forward or aft than a conventional Tunnel Thrusters increasing the turning moment of the hull and therefore requiring less power input.

For added security, all V Series thrusters can be manually lifted in case of power failure. To ensure there is no environmental risk, the main drive motor, hydraulic hoses and electric cables are inside the vessel so are not open to seawater.

H-0400-V
H-0400-V
Specifications
Max Power 63 kW (85 Hp)
Thrust 756 Kgf (1667 Lbf)
Prop Diameter 406 mm (16 in)
Downloads
Vertical Thrusters H-0400-V
PDF Download   DWG Download   STP Download  

H-0400-VR

OYS Vertical Retracting Rotating Thruster
Hydraulic


Specifications
Max Power 63 kW (85 Hp)
Thrust 756 Kgf (1667 Lbf)
Prop Diameter 406 mm (16 in)

H-0500-S

OYS Swing Thruster
Hydraulic

The OYS Swing Thruster benefits from the same in-hub technology as our fixed tunnel thruster, whilst allowing the thruster to fully retract leaving a fair hull with minimal drag. These types of thrusters are usually used in applications where they are positioned within the accommodation area of a vessel. The low profile and compact design allows them to be easily fitted below floor bearers or in low-level lockers / under beds etc.

This compact design uses a lead screw lift assembly with a reduction gear box to ensure that the thruster hub when retracted is held firmly in place and cannot move. In addition, OYS swing thrusters feature a locking pin which adds additional security when locking the leg in the raised position. The main drive motor and hydraulic hoses or cables are fully enclosed within the upper leg assembly so are not open to sea water. OYS has worked with a number of boat builders to optimise the range offered.

H-0500-S
H-0500-S
Specifications
Max Power 99 kW (133 Hp)
Thrust 1188 Kgf (2619 Lbf)
Prop Diameter 508 mm (20 in)
Downloads
Swing Thrusters H-0500-S
PDF Download   DWG Download   STP Download  

H-0500-T

OYS Tunnel Thruster
Hydraulic

T Series tunnel thrusters are compact and easy to fit units that can be supplied complete with steel, aluminium or composite tunnels, pre-drilled ready for installation.

The thruster hub units are protected by twin shaft seals on each propeller shaft and a single shaft seal on the vertical input shaft. The tunnel thruster uses high torque spiral bevel gears and twin contra-rotating propellers to develop a high thrust to tunnel diameter ratio.

T Series thrusters are supplied complete with a mounting saddle, all gaskets/fasteners and a suitable interface for any hydraulic or electric motor. The motor is driven via a flexible coupling to reduce noise and vibration.

H-0500-T
H-0500-T
Specifications
Max Power 99 kW (133 Hp)
Thrust 1188 Kgf (2619 Lbf)
Prop Diameter 508 mm (20 in)
Downloads
Tunnel Thrusters H-0500-T
PDF Download   DWG Download   STP Download  

H-0500-V

OYS Vertical Retracting Thruster
Hydraulic

V Series vertical retracting thrusters benefit from the same in-hub technology as our T Series thrusters, whilst allowing the thruster to fully retract leaving a fair hull with minimal drag. This compact design uses a lead screw lift assembly with a reduction gearbox to ensure that the thruster hub when retracted is held firmly in place.

The Vertical Thruster is also very useful where vessels have a deep V profile so the thruster is fitted higher providing a longer deployment stroke to clear the hull. They can also be fitted further forward or aft than a conventional Tunnel Thrusters increasing the turning moment of the hull and therefore requiring less power input.

For added security, all V Series thrusters can be manually lifted in case of power failure. To ensure there is no environmental risk, the main drive motor, hydraulic hoses and electric cables are inside the vessel so are not open to seawater.

H-0500-V
H-0500-V
Specifications
Max Power 99 kW (133 Hp)
Thrust 1188 Kgf (2619 Lbf)
Prop Diameter 508 mm (20 in)
Downloads
Vertical Thrusters H-0500-V
PDF Download   DWG Download   STP Download  

H-0500-VR

OYS Vertical Retracting Rotating Thruster
Hydraulic


Specifications
Max Power 99 kW (133 Hp)
Thrust 1188 Kgf (2619 Lbf)
Prop Diameter 508 mm (20 in)

H-0600-S

OYS Swing Thruster
Hydraulic

The OYS Swing Thruster benefits from the same in-hub technology as our fixed tunnel thruster, whilst allowing the thruster to fully retract leaving a fair hull with minimal drag. These types of thrusters are usually used in applications where they are positioned within the accommodation area of a vessel. The low profile and compact design allows them to be easily fitted below floor bearers or in low-level lockers / under beds etc.

This compact design uses a lead screw lift assembly with a reduction gear box to ensure that the thruster hub when retracted is held firmly in place and cannot move. In addition, OYS swing thrusters feature a locking pin which adds additional security when locking the leg in the raised position. The main drive motor and hydraulic hoses or cables are fully enclosed within the upper leg assembly so are not open to sea water. OYS has worked with a number of boat builders to optimise the range offered.

H-0600-S
H-0600-S, H-0500-S
Specifications
Max Power 142 kW (191 Hp)
Thrust 1704 Kgf (3757 Lbf)
Prop Diameter 610 mm (24 in)
Downloads
Swing Thrusters H-0600-S
PDF Download   DWG Download   STP Download  

H-0600-T

OYS Tunnel Thruster
Hydraulic

T Series tunnel thrusters are compact and easy to fit units that can be supplied complete with steel, aluminium or composite tunnels, pre-drilled ready for installation.

The thruster hub units are protected by twin shaft seals on each propeller shaft and a single shaft seal on the vertical input shaft. The tunnel thruster uses high torque spiral bevel gears and twin contra-rotating propellers to develop a high thrust to tunnel diameter ratio.

T Series thrusters are supplied complete with a mounting saddle, all gaskets/fasteners and a suitable interface for any hydraulic or electric motor. The motor is driven via a flexible coupling to reduce noise and vibration.

H-0600-T
H-0600-T
Specifications
Max Power 142 kW (191 Hp)
Thrust 1704 Kgf (3757 Lbf)
Prop Diameter 610 mm (24 in)
Downloads
Tunnel Thrusters H-0600-T
PDF Download   DWG Download   STP Download  

H-0600-V

OYS Vertical Retracting Thruster
Hydraulic

V Series vertical retracting thrusters benefit from the same in-hub technology as our T Series thrusters, whilst allowing the thruster to fully retract leaving a fair hull with minimal drag. This compact design uses a lead screw lift assembly with a reduction gearbox to ensure that the thruster hub when retracted is held firmly in place.

The Vertical Thruster is also very useful where vessels have a deep V profile so the thruster is fitted higher providing a longer deployment stroke to clear the hull. They can also be fitted further forward or aft than a conventional Tunnel Thrusters increasing the turning moment of the hull and therefore requiring less power input.

For added security, all V Series thrusters can be manually lifted in case of power failure. To ensure there is no environmental risk, the main drive motor, hydraulic hoses and electric cables are inside the vessel so are not open to seawater.

H-0600-V
H-0600-V
Specifications
Max Power 142 kW (191 Hp)
Thrust 1704 Kgf (3757 Lbf)
Prop Diameter 610 mm (24 in)
Downloads
Vertical Thrusters H-0600-V
PDF Download   DWG Download   STP Download  

H-0600-VR

OYS Vertical Retracting Rotating Thruster
Hydraulic


Specifications
Max Power 142 kW (191 Hp)
Thrust 1704 Kgf (3757 Lbf)
Prop Diameter 610 mm (24 in)

H-0700-S

OYS Swing Thruster
Hydraulic

The OYS Swing Thruster benefits from the same in-hub technology as our fixed tunnel thruster, whilst allowing the thruster to fully retract leaving a fair hull with minimal drag. These types of thrusters are usually used in applications where they are positioned within the accommodation area of a vessel. The low profile and compact design allows them to be easily fitted below floor bearers or in low-level lockers / under beds etc.

This compact design uses a lead screw lift assembly with a reduction gear box to ensure that the thruster hub when retracted is held firmly in place and cannot move. In addition, OYS swing thrusters feature a locking pin which adds additional security when locking the leg in the raised position. The main drive motor and hydraulic hoses or cables are fully enclosed within the upper leg assembly so are not open to sea water. OYS has worked with a number of boat builders to optimise the range offered.

H-0700-S
H-0700-S
Specifications
Max Power 194 kW (260 Hp)
Thrust 2328 Kgf (5132 Lbf)
Prop Diameter 711 mm (28 in)
Downloads
Swing Thrusters H-0700-S
PDF Download   DWG Download   STP Download  

H-0700-T

OYS Tunnel Thruster
Hydraulic

T Series tunnel thrusters are compact and easy to fit units that can be supplied complete with steel, aluminium or composite tunnels, pre-drilled ready for installation.

The thruster hub units are protected by twin shaft seals on each propeller shaft and a single shaft seal on the vertical input shaft. The tunnel thruster uses high torque spiral bevel gears and twin contra-rotating propellers to develop a high thrust to tunnel diameter ratio.

T Series thrusters are supplied complete with a mounting saddle, all gaskets/fasteners and a suitable interface for any hydraulic or electric motor. The motor is driven via a flexible coupling to reduce noise and vibration.

H-0700-T
H-0700-T
Specifications
Max Power 194 kW (260 Hp)
Thrust 2328 Kgf (5132 Lbf)
Prop Diameter 711 mm (28 in)
Downloads
Tunnel Thrusters H-0700-T
PDF Download   DWG Download   STP Download  

H-0700-V

OYS Vertical Retracting Thruster
Hydraulic

V Series vertical retracting thrusters benefit from the same in-hub technology as our T Series thrusters, whilst allowing the thruster to fully retract leaving a fair hull with minimal drag. This compact design uses a lead screw lift assembly with a reduction gearbox to ensure that the thruster hub when retracted is held firmly in place.

The Vertical Thruster is also very useful where vessels have a deep V profile so the thruster is fitted higher providing a longer deployment stroke to clear the hull. They can also be fitted further forward or aft than a conventional Tunnel Thrusters increasing the turning moment of the hull and therefore requiring less power input.

For added security, all V Series thrusters can be manually lifted in case of power failure. To ensure there is no environmental risk, the main drive motor, hydraulic hoses and electric cables are inside the vessel so are not open to seawater.

H-0700-V
H-0700-V
Specifications
Max Power 194 kW (260 Hp)
Thrust 2328 Kgf (5132 Lbf)
Prop Diameter 711 mm (28 in)
Downloads
Vertical Thrusters H-0700-V
PDF Download   DWG Download   STP Download  

H-0700-VR

OYS Vertical Retracting Rotating Thruster
Hydraulic


Specifications
Max Power 194 kW (260 Hp)
Thrust 2328 Kgf (5132 Lbf)
Prop Diameter 711 mm (28 in)

H-0800-S

OYS Swing Thruster
Hydraulic

The OYS Swing Thruster benefits from the same in-hub technology as our fixed tunnel thruster, whilst allowing the thruster to fully retract leaving a fair hull with minimal drag. These types of thrusters are usually used in applications where they are positioned within the accommodation area of a vessel. The low profile and compact design allows them to be easily fitted below floor bearers or in low-level lockers / under beds etc.

This compact design uses a lead screw lift assembly with a reduction gear box to ensure that the thruster hub when retracted is held firmly in place and cannot move. In addition, OYS swing thrusters feature a locking pin which adds additional security when locking the leg in the raised position. The main drive motor and hydraulic hoses or cables are fully enclosed within the upper leg assembly so are not open to sea water. OYS has worked with a number of boat builders to optimise the range offered.

H-0800-S
H-0800-S
Specifications
Max Power 252 kW (338 Hp)
Thrust 2772 Kgf (6111 Lbf)
Prop Diameter 813 mm (32 in)
Downloads
Swing Thrusters H-0800-S
PDF Download   DWG Download   STP Download  

H-0800-T

OYS Tunnel Thruster
Hydraulic

T Series tunnel thrusters are compact and easy to fit units that can be supplied complete with steel, aluminium or composite tunnels, pre-drilled ready for installation.

The thruster hub units are protected by twin shaft seals on each propeller shaft and a single shaft seal on the vertical input shaft. The tunnel thruster uses high torque spiral bevel gears and twin contra-rotating propellers to develop a high thrust to tunnel diameter ratio.

T Series thrusters are supplied complete with a mounting saddle, all gaskets/fasteners and a suitable interface for any hydraulic or electric motor. The motor is driven via a flexible coupling to reduce noise and vibration.

H-0800-T

Specifications
Max Power 252 kW (338 Hp)
Thrust 2772 Kgf (6111 Lbf)
Prop Diameter 813 mm (32 in)
Downloads
Tunnel Thrusters H-0800-T
PDF Download   DWG Download   STP Download  

H-0800-V

OYS Vertical Retracting Thrusters
Hydraulic

V Series vertical retracting thrusters benefit from the same in-hub technology as our T Series thrusters, whilst allowing the thruster to fully retract leaving a fair hull with minimal drag. This compact design uses a lead screw lift assembly with a reduction gearbox to ensure that the thruster hub when retracted is held firmly in place.

The Vertical Thruster is also very useful where vessels have a deep V profile so the thruster is fitted higher providing a longer deployment stroke to clear the hull. They can also be fitted further forward or aft than a conventional Tunnel Thrusters increasing the turning moment of the hull and therefore requiring less power input.

For added security, all V Series thrusters can be manually lifted in case of power failure. To ensure there is no environmental risk, the main drive motor, hydraulic hoses and electric cables are inside the vessel so are not open to seawater.

H-0800-V
H-0800-V
Specifications
Max Power 252 kW (338 Hp)
Thrust 2772 Kgf (6111 Lbf)
Prop Diameter 813 mm (32 in)
Downloads
Vertical Thrusters H-0800-V
PDF Download   DWG Download   STP Download  

H-0800-VR

OYS Vertical Retracting Rotating Thruster
Hydraulic


Specifications
Max Power 252 kW (338 Hp)
Thrust 2772 Kgf (6111 Lbf)
Prop Diameter 813 mm (32 in)

H-0900-S

OYS Swing Thruster
Hydraulic


Specifications
Max Power 319 kW (428 Hp)
Thrust 3509 Kgf (7736 Lbf)
Prop Diameter 914 mm (36 in)

H-0900-V

OYS Vertical Retracting Thruster
Hydraulic


Specifications
Max Power 319 kW (428 Hp)
Thrust 3509 Kgf (7736 Lbf)
Prop Diameter 914 mm (36 in)

H-0900-VR

OYS Vertical Retracting Rotating Thruster
Hydraulic


Specifications
Max Power 319 kW (428 Hp)
Thrust 3509 Kgf (7736 Lbf)
Prop Diameter 914 mm (36 in)

H-1000-S

OYS Swing Thruster
Hydraulic

The OYS Swing Thruster benefits from the same in-hub technology as our fixed tunnel thruster, whilst allowing the thruster to fully retract leaving a fair hull with minimal drag. These types of thrusters are usually used in applications where they are positioned within the accommodation area of a vessel. The low profile and compact design allows them to be easily fitted below floor bearers or in low-level lockers / under beds etc.

This compact design uses a lead screw lift assembly with a reduction gear box to ensure that the thruster hub when retracted is held firmly in place and cannot move. In addition, OYS swing thrusters feature a locking pin which adds additional security when locking the leg in the raised position. The main drive motor and hydraulic hoses or cables are fully enclosed within the upper leg assembly so are not open to sea water. OYS has worked with a number of boat builders to optimise the range offered.

H-1000-S
H-1000-S
Specifications
Max Power 393 kW (527 Hp)
Thrust 4323 Kgf (9506 Lbf)
Prop Diameter 1016 mm (40 in)
Downloads
Swing Thrusters H-1000-S
PDF Download   DWG Download   STP Download  

H-1000-T

OYS Tunnel Thruster
Hydraulic

T Series tunnel thrusters are compact and easy to fit units that can be supplied complete with steel, aluminium or composite tunnels, pre-drilled ready for installation.

The thruster hub units are protected by twin shaft seals on each propeller shaft and a single shaft seal on the vertical input shaft. The tunnel thruster uses high torque spiral bevel gears and twin contra-rotating propellers to develop a high thrust to tunnel diameter ratio.

T Series thrusters are supplied complete with a mounting saddle, all gaskets/fasteners and a suitable interface for any hydraulic or electric motor. The motor is driven via a flexible coupling to reduce noise and vibration.

H-1000-T
H-1000-T
Specifications
Max Power 393 kW (527 Hp)
Thrust 4323 Kgf (9506 Lbf)
Prop Diameter 1016 mm (40 in)
Downloads
Tunnel Thrusters H-1000-T
PDF Download   DWG Download   STP Download  

H-1000-V

OYS Vertical Retracting Thruster
Hydraulic

V Series vertical retracting thrusters benefit from the same in-hub technology as our T Series thrusters, whilst allowing the thruster to fully retract leaving a fair hull with minimal drag. This compact design uses a lead screw lift assembly with a reduction gearbox to ensure that the thruster hub when retracted is held firmly in place.

The Vertical Thruster is also very useful where vessels have a deep V profile so the thruster is fitted higher providing a longer deployment stroke to clear the hull. They can also be fitted further forward or aft than a conventional Tunnel Thrusters increasing the turning moment of the hull and therefore requiring less power input.

For added security, all V Series thrusters can be manually lifted in case of power failure. To ensure there is no environmental risk, the main drive motor, hydraulic hoses and electric cables are inside the vessel so are not open to seawater.

H-1000-V
H-1000-V
Specifications
Max Power 393 kW (527 Hp)
Thrust 4323 Kgf (9506 Lbf)
Prop Diameter 1016 mm (40 in)
Downloads
Vertical Thrusters H-1000-V
PDF Download   DWG Download   STP Download  

H-1000-VR

OYS Vertical Retracting Rotating Thruster
Hydraulic


Specifications
Max Power 393 kW (527 Hp)
Thrust 4323 Kgf (9506 Lbf)
Prop Diameter 1016 mm (40 in)

H-1100-S

OYS Swing Thruster
Hydraulic


Specifications
Max Power 476 kW (638 Hp)
Thrust 5236 Kgf (11543 Lbf)
Prop Diameter 1118 mm (44 in)

H-1100-V

OYS Vertical Retracting Thruster
Hydraulic


Specifications
Max Power 476 kW (638 Hp)
Thrust 5236 Kgf (11543 Lbf)
Prop Diameter 1118 mm (44 in)

H-1100-VR

OYS Vertical Retracting Rotating Thruster
Hydraulic


Specifications
Max Power 476 kW (638 Hp)
Thrust 5236 Kgf (11543 Lbf)
Prop Diameter 1118 mm (44 in)

H-1200-S

OYS Swing Thruster
Hydraulic

The OYS Swing Thruster benefits from the same in-hub technology as our fixed tunnel thruster, whilst allowing the thruster to fully retract leaving a fair hull with minimal drag. These types of thrusters are usually used in applications where they are positioned within the accommodation area of a vessel. The low profile and compact design allows them to be easily fitted below floor bearers or in low-level lockers / under beds etc.

This compact design uses a lead screw lift assembly with a reduction gear box to ensure that the thruster hub when retracted is held firmly in place and cannot move. In addition, OYS swing thrusters feature a locking pin which adds additional security when locking the leg in the raised position. The main drive motor and hydraulic hoses or cables are fully enclosed within the upper leg assembly so are not open to sea water. OYS has worked with a number of boat builders to optimise the range offered.

H-1200-S
H-1200-S
Specifications
Max Power 565 kW (758 Hp)
Thrust 6215 Kgf (13702 Lbf)
Prop Diameter 1219 mm (48 in)
Downloads
Swing Thrusters H-1200-S
PDF Download   DWG Download   STP Download  

H-1200-T

OYS Tunnel Thruster
Hydraulic

T Series tunnel thrusters are compact and easy to fit units that can be supplied complete with steel, aluminium or composite tunnels, pre-drilled ready for installation.

The thruster hub units are protected by twin shaft seals on each propeller shaft and a single shaft seal on the vertical input shaft. The tunnel thruster uses high torque spiral bevel gears and twin contra-rotating propellers to develop a high thrust to tunnel diameter ratio.

T Series thrusters are supplied complete with a mounting saddle, all gaskets/fasteners and a suitable interface for any hydraulic or electric motor. The motor is driven via a flexible coupling to reduce noise and vibration.

H-1200-T
H-1200-T
Specifications
Max Power 565 kW (758 Hp)
Thrust 6215 Kgf (13702 Lbf)
Prop Diameter 1219 mm (48 in)
Downloads
Tunnel Thrusters H-1200-T
PDF Download   DWG Download   STP Download  

H-1200-V

OYS Vertical Retracting Thruster
Hydraulic

V Series vertical retracting thrusters benefit from the same in-hub technology as our T Series thrusters, whilst allowing the thruster to fully retract leaving a fair hull with minimal drag. This compact design uses a lead screw lift assembly with a reduction gearbox to ensure that the thruster hub when retracted is held firmly in place.

The Vertical Thruster is also very useful where vessels have a deep V profile so the thruster is fitted higher providing a longer deployment stroke to clear the hull. They can also be fitted further forward or aft than a conventional Tunnel Thrusters increasing the turning moment of the hull and therefore requiring less power input.

For added security, all V Series thrusters can be manually lifted in case of power failure. To ensure there is no environmental risk, the main drive motor, hydraulic hoses and electric cables are inside the vessel so are not open to seawater.

H-1200-V
H-1200-V
Specifications
Max Power 565 kW (758 Hp)
Thrust 6215 Kgf (13702 Lbf)
Prop Diameter 1219 mm (48 in)
Downloads
Vertical Thrusters H-1200-V
PDF Download   DWG Download   STP Download  

H-1200-VR

OYS Vertical Retracting Rotating Thruster
Hydraulic


Specifications
Max Power 565 kW (758 Hp)
Thrust 6215 Kgf (13702 Lbf)
Prop Diameter 1219 mm (48 in)

H-1300-S

OYS Swing Thruster
Hydraulic


Specifications
Max Power 663 kW (889 Hp)
Thrust 7293 Kgf (16078 Lbf)
Prop Diameter 1321 mm (52 in)

H-1300-V

OYS Vertical Retracting Thruster
Hydraulic


Specifications
Max Power 663 kW (889 Hp)
Thrust 7293 Kgf (16078 Lbf)
Prop Diameter 1321 mm (52 in)

H-1300-VR

OYS Vertical Retracting Rotating Thruster
Hydraulic


Specifications
Max Power 663 kW (889 Hp)
Thrust 7293 Kgf (16078 Lbf)
Prop Diameter 1321 mm (52 in)

H-1400-VR

OYS Vertical Retracting Rotating Thruster
Hydraulic


Specifications
Max Power 768 kW (1030 Hp)
Thrust 8448 Kgf (18624 Lbf)
Prop Diameter 1422 mm (56 in)